CCENT Study Guide Chapter 6 Cisco’s Internetworking Operating

CCENT Study Guide Chapter 6 Cisco’s Internetworking Operating System (IOS)

Chapter 6 Objectives The CCENT Topics Covered in this chapter include: 2.0 LAN Switching Technologies 2.3 Troubleshoot interface and cable issues (collisions, errors, duplex, speed). 5.0 Infrastructure Management 5.3 Configure and verify initial device configuration. 5.4 Configure, verify, and troubleshoot basic device hardening. 5.4.a Local authentication 5.4.b Secure password 5.4.c Access to device 5.4.c. (i) Voice 5.4.c. (ii) Video 5.4.c. (iii) Data 5.4.d Source address Telnet/SSH 5.4.e Login banner 5.6 Use Cisco IOS tools to troubleshoot and resolve problems. 5.6.a Ping and traceroute with extended option 5.6.b Terminal monitor 5.6.c Log events 2

Cisco 2960 switch and 1900 series router

Bringing Up a Switch When you first bring up a Cisco IOS device, it will run a power-on self-test—a POST. Upon passing that, the machine will look for and then load the Cisco IOS from flash memory if an IOS file is present, then expand it into RAM. As you probably know, flash memory is electronically erasable programmable read-only memory—an EEPROM. The next step is for the IOS to locate and load a valid configuration known as the startup-config that will be stored in nonvolatile RAM (NVRAM). Once the IOS is loaded and up and running, the startupconfig will be copied from NVRAM into RAM and from then on referred to as the running-config. But if a valid IOS isn’t found in NVRAM, your switch will enter setup mode, giving you a step-by-step dialog to help configure some basic parameters on it.

Command-Line Interface (CLI) After the interface status messages appear and you press Enter, the Switch prompt will pop up. This is called user exec mode, or user mode for short, and although it’s mostly used to view statistics, it is also a stepping stone along the way to logging in to privileged exec mode, called privileged mode for short. You can view and change the configuration of a Cisco router only while in privileged mode, and you enter it via the enable command like this: Switch enable Switch#

Defining Router Terms Table 6.1 defines some of the terms I’ve used so far. Table 6.1: Router terms Mode Definition User exec mode Limited to basic monitoring commands Privileged exec mode Provides access to all other router commands Global configuration mode Commands that affect the entire system [AU: Includes commands that affect ? Also in the next one? Doesn’t seem like the mode is commands.]leavee Specific configuration modes Commands that affect interfaces/processes only Setup mode Interactive configuration dialog

Table 6.2: Enhanced editing commands Table 6.2 lists the enhanced editing commands available on a Cisco router. Table 6.2: Enhanced editing commands Command Meaning Ctrl A Moves your cursor to the beginning of the line Ctrl E Moves your cursor to the end of the line Esc B Moves back one word Ctrl B Moves back one character Ctrl F Moves forward one character Esc F Moves forward one word Ctrl D Deletes a single character Backspace Deletes a single character Ctrl R Redisplays a line Ctrl U Erases a line Ctrl W Erases a word Ctrl Z Ends configuration mode and returns to EXEC Tab Finishes typing a command for you

Table 6.3: Router-command history You can review the router-command history with the commands shown in Table 6.3. Table 6.3: Router-command history Command Meaning Ctrl P or up arrow Shows last command entered Ctrl N or down arrow Shows previous commands entered show history Shows last 20 commands entered by default show terminal Shows terminal configurations and history buffer size terminal history size Changes buffer size (max 256)

Administrative Functions You can configure the following administrative functions on a router and switch: Hostnames Banners Passwords Interface descriptions

Hostnames/Banner We use the hostname command to set the identity of the router. This is only locally significant, meaning it doesn’t affect how the router performs name lookups or how the device actually works on the internetwork. Switch#config t Switch(config)#hostname Todd Message of the day (MOTD) banners are the most widely used banners because they give a message to anyone connecting to the router via Telnet or an auxiliary port or even through a console port as seen here: Todd(config)#banner motd ? LINE c banner-text c, where ‘c’ is a delimiting character Todd(config)#banner motd # Enter TEXT message. End with the character ‘#’. Acme.com network, then you must disconnect immediately. # Todd(config)# Z (Press the control key z keys to return to privileged mode)

Passwords Enable password/enable secret Todd(config)#enable secret todd Todd(config)#enable password todd The enable password you have chosen is the same as your enable secret. This is not recommended. Re-enter the enable password. You wont use the older enable password in today’s networks.

Console/VTY passwords User-mode passwords are assigned via the line command like this: Todd(config)#line ? 0-16 First Line number console Primary terminal line vty Virtual terminal

SSH 1. Set your hostname: Router(config)#hostname Todd 2. Set the domain name—both the hostname and domain name are required for the encryption keys to be generated: Todd(config)#ip domain-name Lammle.com 3. Set the username to allow SSH client access: Todd(config)#username Todd password Lammle 4. Generate the encryption keys for securing the session: Todd(config)#crypto key generate rsa 5. Enable SSH version 2 on the router—not mandatory, but strongly suggested: Todd(config)#ip ssh version 2 6. Connect to the VTY lines of the switch: Todd(config)#line vty 0 15 7. Configure your access protocols: Todd(config-line)#transport input ? all All protocols none No protocols ssh TCP/IP SSH protocol telnet TCP/IP Telnet protocol Todd(config-line)#transport input ssh ? telnet TCP/IP Telnet protocol cr But if you want to go with Telnet, here’s how you do that: Todd(config-line)#transport input ssh telnet

Encrypting Your Passwords To manually encrypt your passwords, use the service password-encryption command. Here’s how: Todd#config t Todd(config)#service passwordencryption Todd(config)#exit Todd#show run Building configuration. ! ! enable secret 4 ykw.3/tgsOuy9.6qmgG/EeYOYgBvfX4v.S8UNA9R ddg

Descriptions Setting descriptions on an interface is another administratively helpful thing, and like the hostname, it’s also only locally significant. Todd#config t Todd(config)#int fa0/1 Todd(config-if)#description Sales VLAN Trunk Link Todd(config-if)# Z Todd# And on a router serial WAN: Router#config t Router(config)#int s0/0/0 Router(config-if)#description WAN to Miami Router(config-if)# Z

Verifying interfaces Todd#sh ip interface brief Interface IP-Address Vlan1 192.168.255.8 FastEthernet0/1 unassigned FastEthernet0/2 unassigned FastEthernet0/3 unassigned FastEthernet0/4 unassigned FastEthernet0/5 unassigned FastEthernet0/6 unassigned FastEthernet0/7 unassigned FastEthernet0/8 unassigned GigabitEthernet0/1 unassigned OK? YES YES YES YES YES YES YES YES YES YES Method DHCP unset unset unset unset unset unset unset unset unset Status up up up down down up up down down down Protocol up up up down down up up down down down

Bringing Up an Interface If an interface is shut down, it’ll display as administratively down when you use the show interfaces command (sh int for short): Router#sh int f0/0 FastEthernet0/1 is administratively down, line protocol is down [output cut] You can bring up the router interface with the no shutdown command (no shut for short): Router(config)#int f0/0 Router(config-if)#no shutdown *August 21 13:45:08.455: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up Router(config-if)#do show int f0/0 FastEthernet0/0 is up, line protocol is up [output cut]

Serial Interface Commands Figure 6.3: A typical WAN connection. Clocking is typically provided by a DCE network to routers. In nonproduction environments, a DCE network is not always present.

Figure 6.4: Providing clocking on a nonproduction network

Viewing, Saving, and Erasing Configurations You can manually save the file from DRAM, which is usually just called RAM, to NVRAM by using the copy running-config startup-config command. You can use the shortcut copy run start as well: Todd#copy running-config startup-config Destination filename [startup-config]? [press enter] Building configuration. [OK] Todd# Building configuration. When you see a question with an answer in [], it means that if you just press Enter, you’re choosing the default answer.

Show running-config You can view the files by typing show running-config or show startup-config from privileged mode. The sh run command, which is a shortcut for show running-config, tells us that we’re viewing the current configuration: Todd#sh run Building configuration. Current configuration : 855 bytes ! ! Last configuration change at 23:20:06 UTC Mon Mar 1 1993 ! version 15.0 [output cut] NOTE: You can see the version of IOS with the show running-config command.

Show startup-config The sh start command—one of the shortcuts for the show startupconfig command—shows us the configuration that will be used the next time the router is reloaded. It also tells us how much NVRAM is being used to store the startup-config file. N O T Todd#sh start Using 855 out of 524288 bytes ! ! Last configuration change at 23:20:06 UTC Mon Mar 1 1993 ! version 15.0 [output cut] But beware—if you try and view the configuration and see Todd#sh start startup-config is not present you have not saved your running-config to NVRAM, or you’ve deleted the backup configuration! Let me talk about just how you would do that now.

Written Labs and Review Questions – Read through the Exam Essentials section together in class. – Open your books and go through all the written labs and the review questions. – Review the answers in class. 23